Experimental study of the formation of surface roughness of the sprayed ceramic layer on the necks of the rotor shafts of gas turbine
The applied sprayed coatings are absolutely new materials, which differ from the initial components by their formation history, bond nature, etc. In general mechanical engineering standards, there are no recommendations on selection of grinding modes of sprayed ceramic coatings. Therefore, at the de...
Збережено в:
Видавець: | Journal of Mechanical Engineering |
---|---|
Дата: | 2014 |
Автори: | , |
Формат: | Стаття |
Мова: | Russian |
Опубліковано: |
Journal of Mechanical Engineering
2014
|
Теми: | |
Онлайн доступ: | https://journals.uran.ua/jme/article/view/19913 |
Теги: |
Додати тег
Немає тегів, Будьте першим, хто поставить тег для цього запису!
|
Репозиторії
Journal of Mechanical Engineeringid |
journalsuranuajme-article-19913 |
---|---|
record_format |
ojs |
spelling |
journalsuranuajme-article-199132024-06-01T14:40:55Z Experimental study of the formation of surface roughness of the sprayed ceramic layer on the necks of the rotor shafts of gas turbine Экспериментальное исследование формирования шероховатости поверхности напыленного керамического слоя на шейках валов ротора газовой турбины Експерементальне дослідження формування шорсткості поверхні напиленого керамічного шару на шийках валів ротора газової турбіни Лебедев, Владимир Чумаченко, Татьяна mineral-ceramic layer grinding wear roughness cubic boron nitride wheel УДК 621.791 минералокерамический слой шлифование износ шероховатость круг из кубического нитрида бора УДК 621.791 мінералокерамічний шар шліфування знос шорсткість коло з кубічного нітриду бору УДК 621.791 The applied sprayed coatings are absolutely new materials, which differ from the initial components by their formation history, bond nature, etc. In general mechanical engineering standards, there are no recommendations on selection of grinding modes of sprayed ceramic coatings. Therefore, at the design of grinding operations of the sprayed layers it is necessary to carry out the selection of the grinding wheel and processing modes on the basis of the conditions of the maximum productivity, economic efficiency and assurance of the required surface quality.Therefore, the studies, aimed at technological pro-vision of quality and productiveness of grinding of the necks of rotor shafts of gas turbine, sprayed with wear- and heat-resistant mineral-ceramic coating are topical for mechanical engineering.In the literature, referring to ceramics processing, there are no data on the processing of the sprayed mineral-ceramic layer. The ceramics were processed by wheels only on metal and organic bonds.According to technical requirements, the necks of the shaft of gas turbine must have low values of surface roughness Ra = 0,63…0,32. This class of roughness at abrasive grinding is reached as a result of additional fin-ishing operations. Therefore, the possibilities of grinding by cubic boron nitride wheels can be applied to the full extent.The study of regularities of the surface roughness from processing factors allows to manage the process so that steadily maintain the required roughness value. В статье рассмотрены закономерности изменения шероховатости напыленного минералокерамического слоя на шейках валов ротора газовой турбины в зависимости от режимов шлифования и зернистости круга из кубического нитрида бора. Шероховатость поверхности при шлифовании напыленного керамического слоя, состоящего из чистого Al2О3 находится в пределах Ra = 0,63…0,32, для модифицированного TiС и С шероховатость поверхности практически не меняется, а модифицированного WC повышается на один разряд. Розглянуті закономірності зміни шорсткості напиленого мінералокерамічного шару на шийках валів ротора газової турбіни залежно від режимів шліфування і зернистості круга з кубічного нітриду бору. Шорсткість поверхні при шліфуванні напиленого керамічного шару, що складається з чистого Al2О3, знаходиться в межах Ra = 0,63 ... 0,32, для модифікованого TiС і С шорсткість поверхні практично не змінюється, а модифікованого WC – підвищується на один розряд. Journal of Mechanical Engineering Проблемы машиностроения Проблеми машинобудування 2014-01-10 Article Article application/pdf https://journals.uran.ua/jme/article/view/19913 Journal of Mechanical Engineering; Vol. 16 No. 5 (2013); 3-6 Проблемы машиностроения; Том 16 № 5 (2013); 3-6 Проблеми машинобудування; Том 16 № 5 (2013); 3-6 2709-2992 2709-2984 ru https://journals.uran.ua/jme/article/view/19913/36489 Copyright (c) 2015 Владимир Лебедев, Татьяна Чумаченко https://creativecommons.org/licenses/by-nd/4.0 |
institution |
Journal of Mechanical Engineering |
collection |
OJS |
language |
Russian |
topic |
mineral-ceramic layer grinding wear roughness cubic boron nitride wheel УДК 621.791 минералокерамический слой шлифование износ шероховатость круг из кубического нитрида бора УДК 621.791 мінералокерамічний шар шліфування знос шорсткість коло з кубічного нітриду бору УДК 621.791 |
spellingShingle |
mineral-ceramic layer grinding wear roughness cubic boron nitride wheel УДК 621.791 минералокерамический слой шлифование износ шероховатость круг из кубического нитрида бора УДК 621.791 мінералокерамічний шар шліфування знос шорсткість коло з кубічного нітриду бору УДК 621.791 Лебедев, Владимир Чумаченко, Татьяна Experimental study of the formation of surface roughness of the sprayed ceramic layer on the necks of the rotor shafts of gas turbine |
topic_facet |
mineral-ceramic layer grinding wear roughness cubic boron nitride wheel УДК 621.791 минералокерамический слой шлифование износ шероховатость круг из кубического нитрида бора УДК 621.791 мінералокерамічний шар шліфування знос шорсткість коло з кубічного нітриду бору УДК 621.791 |
format |
Article |
author |
Лебедев, Владимир Чумаченко, Татьяна |
author_facet |
Лебедев, Владимир Чумаченко, Татьяна |
author_sort |
Лебедев, Владимир |
title |
Experimental study of the formation of surface roughness of the sprayed ceramic layer on the necks of the rotor shafts of gas turbine |
title_short |
Experimental study of the formation of surface roughness of the sprayed ceramic layer on the necks of the rotor shafts of gas turbine |
title_full |
Experimental study of the formation of surface roughness of the sprayed ceramic layer on the necks of the rotor shafts of gas turbine |
title_fullStr |
Experimental study of the formation of surface roughness of the sprayed ceramic layer on the necks of the rotor shafts of gas turbine |
title_full_unstemmed |
Experimental study of the formation of surface roughness of the sprayed ceramic layer on the necks of the rotor shafts of gas turbine |
title_sort |
experimental study of the formation of surface roughness of the sprayed ceramic layer on the necks of the rotor shafts of gas turbine |
title_alt |
Экспериментальное исследование формирования шероховатости поверхности напыленного керамического слоя на шейках валов ротора газовой турбины Експерементальне дослідження формування шорсткості поверхні напиленого керамічного шару на шийках валів ротора газової турбіни |
description |
The applied sprayed coatings are absolutely new materials, which differ from the initial components by their formation history, bond nature, etc. In general mechanical engineering standards, there are no recommendations on selection of grinding modes of sprayed ceramic coatings. Therefore, at the design of grinding operations of the sprayed layers it is necessary to carry out the selection of the grinding wheel and processing modes on the basis of the conditions of the maximum productivity, economic efficiency and assurance of the required surface quality.Therefore, the studies, aimed at technological pro-vision of quality and productiveness of grinding of the necks of rotor shafts of gas turbine, sprayed with wear- and heat-resistant mineral-ceramic coating are topical for mechanical engineering.In the literature, referring to ceramics processing, there are no data on the processing of the sprayed mineral-ceramic layer. The ceramics were processed by wheels only on metal and organic bonds.According to technical requirements, the necks of the shaft of gas turbine must have low values of surface roughness Ra = 0,63…0,32. This class of roughness at abrasive grinding is reached as a result of additional fin-ishing operations. Therefore, the possibilities of grinding by cubic boron nitride wheels can be applied to the full extent.The study of regularities of the surface roughness from processing factors allows to manage the process so that steadily maintain the required roughness value. |
publisher |
Journal of Mechanical Engineering |
publishDate |
2014 |
url |
https://journals.uran.ua/jme/article/view/19913 |
work_keys_str_mv |
AT lebedevvladimir experimentalstudyoftheformationofsurfaceroughnessofthesprayedceramiclayeronthenecksoftherotorshaftsofgasturbine AT čumačenkotatʹâna experimentalstudyoftheformationofsurfaceroughnessofthesprayedceramiclayeronthenecksoftherotorshaftsofgasturbine AT lebedevvladimir éksperimentalʹnoeissledovanieformirovaniâšerohovatostipoverhnostinapylennogokeramičeskogosloânašejkahvalovrotoragazovojturbiny AT čumačenkotatʹâna éksperimentalʹnoeissledovanieformirovaniâšerohovatostipoverhnostinapylennogokeramičeskogosloânašejkahvalovrotoragazovojturbiny AT lebedevvladimir eksperementalʹnedoslídžennâformuvannâšorstkostípoverhnínapilenogokeramíčnogošarunašijkahvalívrotoragazovoíturbíni AT čumačenkotatʹâna eksperementalʹnedoslídžennâformuvannâšorstkostípoverhnínapilenogokeramíčnogošarunašijkahvalívrotoragazovoíturbíni |
first_indexed |
2024-06-01T14:42:18Z |
last_indexed |
2024-06-01T14:42:18Z |
_version_ |
1800670217512157184 |