Effect of Forging on Cyclic Hardening Behavior of CW 614 Brass Alloy
Проведено исследование циклического упрочнения латуни CW 614 на образцах, изготовленных
 по двум технологиям: промышленная и путем ковки. Для каждого типа образца установлены
 особенности циклического упрочнения и циклической петли гистерезиса. Представлены результаты анализа процесс...
Saved in:
| Published in: | Проблемы прочности |
|---|---|
| Date: | 2011 |
| Main Authors: | Mnif, R., Elleuch, R., Elleuch, K., Haddar, N., Halouani, F. |
| Format: | Article |
| Language: | English |
| Published: |
Інститут проблем міцності ім. Г.С. Писаренко НАН України
2011
|
| Subjects: | |
| Online Access: | https://nasplib.isofts.kiev.ua/handle/123456789/112749 |
| Tags: |
Add Tag
No Tags, Be the first to tag this record!
|
| Journal Title: | Digital Library of Periodicals of National Academy of Sciences of Ukraine |
| Cite this: | Effect of Forging on Cyclic Hardening Behavior of CW 614 Brass Alloy / R. Mnif, R. Elleuch, K. Elleuch, N. Haddar, F. Halouani // Проблемы прочности. — 2011. — № 2. — С. 145-152. — Бібліогр.: 17 назв. — англ. |
Institution
Digital Library of Periodicals of National Academy of Sciences of UkraineSimilar Items
Effect of the Microcrack Inclination Angle on Crack Propagation Behavior of TiAl Alloy
by: Feng, R.C., et al.
Published: (2017)
by: Feng, R.C., et al.
Published: (2017)
A Theoretical and Experimental Analysis of Rotary Compression of Hollow Forgings Formed Over a Mandrel
by: Tomczak, J., et al.
Published: (2017)
by: Tomczak, J., et al.
Published: (2017)
Evolution of discrete phenomena of inelasticity in aluminum alloy under cyclic loading
by: Pisarenko, G.G., et al.
Published: (2009)
by: Pisarenko, G.G., et al.
Published: (2009)
Analysis of Residual Stresses during Heat Treatment of Large Forged Shafts Considering Transformation Plasticity and Creep Deformation
by: Yanagisawa, Y., et al.
Published: (2017)
by: Yanagisawa, Y., et al.
Published: (2017)
Investigation of Plastic Behavior of Alloyed Steel Deformed during Martensitic Transformation
by: Kandrotaitė-Janutienė, R., et al.
Published: (2016)
by: Kandrotaitė-Janutienė, R., et al.
Published: (2016)
Short Fatigue Crack Behavior of LZ50 Axle Steel under Rotating-Bending Cyclic Loading
by: Yang, B., et al.
Published: (2018)
by: Yang, B., et al.
Published: (2018)
Analysis of Gas Nitriding Characteristics under Different Cold Hardening and Nitriding Pressure Conditions for Low-Carbon Low-Alloy Steel
by: Zhou, Z A., et al.
Published: (2018)
by: Zhou, Z A., et al.
Published: (2018)
Experimental and Numerical Analysis of Springback Behavior of Aluminum Alloys
by: Slota, J., et al.
Published: (2017)
by: Slota, J., et al.
Published: (2017)
Effect of Aging Treatment on Surface Roughness, Mechanical Properties, and Fracture Behavior of 6xxx and 7xxx Aluminum Alloys
by: Sevim, I., et al.
Published: (2014)
by: Sevim, I., et al.
Published: (2014)
Cyclic Inelasticity and High-Cycle Fatigue of Metals with Consideration of the Stress Gradient Effect
by: Troshchenko, V.T.
Published: (2011)
by: Troshchenko, V.T.
Published: (2011)
Corrosion behavior of 20 steel, copper, brass and aluminum in inhibited acid solutions
by: Z. V. Slobodian, et al.
Published: (2020)
by: Z. V. Slobodian, et al.
Published: (2020)
Effect of Cyclic Stresses below the Endurance Limit on the Fatigue Life of 40Cr Steel
by: Zhao, L.H., et al.
Published: (2018)
by: Zhao, L.H., et al.
Published: (2018)
Constitutive description of creep behavior of Mg-4 Al-1Ca alloy
by: Milicka, K., et al.
Published: (2008)
by: Milicka, K., et al.
Published: (2008)
Fiber Laser Welding of Dual-Phase and Bake-Hardened Steels
by: Švec, P., et al.
Published: (2016)
by: Švec, P., et al.
Published: (2016)
Effect of Pores on Mechanical Behavior. Application to the Composite Material
by: Salih, A., et al.
Published: (2002)
by: Salih, A., et al.
Published: (2002)
Surface Strengthening Behavior of Magnesium Alloy with Laser Thermal Loading under Rapid Cooling
by: Ge, Y.Q., et al.
Published: (2018)
by: Ge, Y.Q., et al.
Published: (2018)
Fatigue behavior of dissimilar friction stir welds between cast and wrought aluminum alloys
by: Uematsu, Y., et al.
Published: (2008)
by: Uematsu, Y., et al.
Published: (2008)
Accelerating Effects of Cyclic Creep Due to the Alternative Load Compared with Constant Load for CD 304L
by: Daei-Sorkhabi, A.H., et al.
Published: (2015)
by: Daei-Sorkhabi, A.H., et al.
Published: (2015)
Crack initiation and endurance limit of hard steels under multiaxial cyclic loads
by: Bomas, H., et al.
Published: (2008)
by: Bomas, H., et al.
Published: (2008)
Constitutive Behavior of 4343/4A60 Aluminum Alloy at Multi-Pass Hot Deformation
by: Tang, C., et al.
Published: (2017)
by: Tang, C., et al.
Published: (2017)
Comparison between Isothermal and Non-Isothermal Fatigue Behavior in a Cast Aluminum-Silicon-Magnesium Alloy
by: Azadi, M., et al.
Published: (2015)
by: Azadi, M., et al.
Published: (2015)
Cyclic cracking resistance of brittle materials in compressive loading
by: Lanin, A.G.
Published: (2009)
by: Lanin, A.G.
Published: (2009)
Corrosion fatigue behavior of extruded AZ80, AZ61, and AM60 magnesium alloys in distilled water
by: Uematsu, Y., et al.
Published: (2008)
by: Uematsu, Y., et al.
Published: (2008)
Notch Effect on the Fatigue Behavior of a Hot Dip Galvanized Structural Steel
by: Berto, F., et al.
Published: (2015)
by: Berto, F., et al.
Published: (2015)
Cyclic Plastic Response and Damage in Materials for High Temperature Applications
by: Polák, J., et al.
Published: (2014)
by: Polák, J., et al.
Published: (2014)
Anodic solution a-brass
by: V. V. Datsenko, et al.
Published: (2014)
by: V. V. Datsenko, et al.
Published: (2014)
Effect of Braiding Angle on the Impact and Post-Impact Behavior of 3D Braided Composites
by: Yan, S., et al.
Published: (2017)
by: Yan, S., et al.
Published: (2017)
Theoretical Construction of Initial and Subsequent Yield Surfaces for Isotropic Strain-Hardening Elastoplastic Materials of the Differential Type
by: Lepikhin, P.P.
Published: (2010)
by: Lepikhin, P.P.
Published: (2010)
Mechanical properties and fracture behavior of high-strength steels
by: Musalek, R., et al.
Published: (2008)
by: Musalek, R., et al.
Published: (2008)
Formability of Tailor-Welded Blanks from Dual-Phase and Bake-Hardened Steels with a Planar Anisotropy Influence
by: Schrek, A., et al.
Published: (2017)
by: Schrek, A., et al.
Published: (2017)
Elastoplastic Damage Model for Concrete under Triaxial Compression and Reversed Cyclic Loading
by: Zhang, J., et al.
Published: (2018)
by: Zhang, J., et al.
Published: (2018)
Residual Strains of Filter Materials Reinforced with Grid Inclusions under Cyclic Loading
by: Lin, Y.L., et al.
Published: (2015)
by: Lin, Y.L., et al.
Published: (2015)
Evaluation of the limit state and cyclic life of structural materials under thermal fatigue
by: Gopkalo, A.P.
Published: (2009)
by: Gopkalo, A.P.
Published: (2009)
Bond Strength Deterioration of Reinforced and Prestressed Concrete Members at Reversed Cyclic Loads
by: Lee, J.-Y., et al.
Published: (2015)
by: Lee, J.-Y., et al.
Published: (2015)
Stacking Sequence Effect on the Fracture Behavior of Narrow L-Shaped Cross-Ply Laminates: Experimental Study
by: Pan, Z.Y., et al.
Published: (2018)
by: Pan, Z.Y., et al.
Published: (2018)
Flexural Fatigue Behavior of Cross-Ply Laminates: An Experimental Approach
by: Bezazi, A.R., et al.
Published: (2003)
by: Bezazi, A.R., et al.
Published: (2003)
Influence of nitriding on the fatigue behavior and fracture micromechanisms of nodular cast Iron
by: Konecna, R., et al.
Published: (2008)
by: Konecna, R., et al.
Published: (2008)
Strength Degradation of Glass Fiber Reinforced Polymer Bars Subjected to Reversed Cyclic Load
by: Lee, J.Y., et al.
Published: (2014)
by: Lee, J.Y., et al.
Published: (2014)
Coupled Effects of Strain Rate and Temperature on Deformation Twinning in Cu-Zn Alloy
by: Zhou, P., et al.
Published: (2016)
by: Zhou, P., et al.
Published: (2016)
Effect of carbon on the corrosion behavior of thermally hardened rolled products
by: V. H. Razdobrieiev
Published: (2020)
by: V. H. Razdobrieiev
Published: (2020)
Similar Items
-
Effect of the Microcrack Inclination Angle on Crack Propagation Behavior of TiAl Alloy
by: Feng, R.C., et al.
Published: (2017) -
A Theoretical and Experimental Analysis of Rotary Compression of Hollow Forgings Formed Over a Mandrel
by: Tomczak, J., et al.
Published: (2017) -
Evolution of discrete phenomena of inelasticity in aluminum alloy under cyclic loading
by: Pisarenko, G.G., et al.
Published: (2009) -
Analysis of Residual Stresses during Heat Treatment of Large Forged Shafts Considering Transformation Plasticity and Creep Deformation
by: Yanagisawa, Y., et al.
Published: (2017) -
Investigation of Plastic Behavior of Alloyed Steel Deformed during Martensitic Transformation
by: Kandrotaitė-Janutienė, R., et al.
Published: (2016)