Hydrogen technology of energy storage making use of wind power potential
Описывается разработка универсальных технологий, которые могут быть использованы для обеспечения непрерывной работы опреснительной установки при использовании энергии ветра. Рассмотрены основные принципы реализации электрохимического метода получения водорода и кислорода высокого давления из воды с...
Збережено в:
| Дата: | 2017 |
|---|---|
| Автори: | , , , , , |
| Формат: | Стаття |
| Мова: | English |
| Опубліковано: |
Інстиут проблем машинобудування ім. А.М. Підгорного НАН України
2017
|
| Назва видання: | Проблемы машиностроения |
| Теми: | |
| Онлайн доступ: | https://nasplib.isofts.kiev.ua/handle/123456789/115665 |
| Теги: |
Додати тег
Немає тегів, Будьте першим, хто поставить тег для цього запису!
|
| Назва журналу: | Digital Library of Periodicals of National Academy of Sciences of Ukraine |
| Цитувати: | Hydrogen technology of energy storage making use of wind power potential / V. Solovey, L. Kozak, A. Shevchenko, M. Zipunnikov, R. Campbell, F. Seamon // Проблемы машиностроения. — 2017. — Т. 20, № 1. — С. 62-68. — Бібліогр.: 7 назв. — англ. |
Репозитарії
Digital Library of Periodicals of National Academy of Sciences of Ukraine| id |
nasplib_isofts_kiev_ua-123456789-115665 |
|---|---|
| record_format |
dspace |
| spelling |
nasplib_isofts_kiev_ua-123456789-1156652025-02-09T15:52:28Z Hydrogen technology of energy storage making use of wind power potential Solovey, V. Kozak, L. Shevchenko, A. Zipunnikov, M. Campbell, R. Seamon, F. Нетрадиционная энергетика Описывается разработка универсальных технологий, которые могут быть использованы для обеспечения непрерывной работы опреснительной установки при использовании энергии ветра. Рассмотрены основные принципы реализации электрохимического метода получения водорода и кислорода высокого давления из воды с использованием материалов электродов с переменной валентностью. Предложена система хранения химической энергии в виде сжатого водорода до высоких давлений с последующим его использованием в топливном элементе. Разработанная система характеризуется повышением надежности и эксплуатационной безопасности. Водород-накопительная система позволяет контролировать для установок потребляемую мощность. Это особенно важно, когда основным источником энергии для электролизной установки служит энергия ветра, которая не является постоянной и зависит от климатических факторов. Даны рекомендации по применению данного способа получения водорода (кислорода) с использованием в качестве первичного источника возобновляемых видов энергии (солнца, ветра), отличающихся непостоянством поступления. Сформированы научно-технические принципы создания электрохимических водородных аккумуляторов энергии и предложены пути оптимизации их работы на переменных режимах, характерных для реальных условий эксплуатации энерготехнологических комплексов на базе ветроэнергетической станции. Приведены стоимостные показатели создания и эксплуатации системы генерации водорода в зависимости от уровня давления в электролизере. Описується розробка універсальних технологій, які можуть бути застосовані для забезпечення безперервної роботи опріснювальної установки при використанні енергії вітру. Розглянуто основні принципи реалізації електрохімічного методу отримання водню та кисню високого тиску з води із використанням матеріалів електродів зі змінною валентністю. Запропоновано систему зберігання хімічної енергії у вигляді стисненого водню до високих тисків з подальшим його застосуванням в паливному елементі, яка характеризується підвищенням надійності та експлуатаційної безпеки. Надано рекомендації із застосування даного способу отримання водню (кисню) з використанням як первинного джерела відновлюваних видів енергії, що відрізняються непостійністю надходження (сонце, вітер). This article describes the development of the versatile technology that can be used to provide continuous power for a desalination plant using wind energy. There were studied the main principles to realize the electrochemical method of high pressure hydrogen and oxygen generation with the use of variable-valency metals as electrodes. We propose the high reliable and operational safety system to store chemical energy as high pressure hydrogen for later use in the fuel cells. Such hydrogen generation and storage system allows the chemical reaction rate to be controlled by controlling the current intensity and, hence, the consumed power can be controlled. This is especially important when the primary energy source for the electrolysis installation is wind power, which is not constant and is affected by climatic factors. The article provides the recommendations as to application of this versatile technology to generate hydrogen (oxygen) using the changeable wind or sun renewable energy as the primary energy sources. Scientific and technical principles for creation of the energy electrochemical hydrogen accumulators are formed and the ways are proposed to optimize their operation under variable modes, which represent the real conditions of exploitation of energy-technological complexes created on the base of the wind power stations. Cost indexes over of creation and exploitation of the hydrogen generation system are presented depending on the pressure level in an electrolyzer. 2017 Article Hydrogen technology of energy storage making use of wind power potential / V. Solovey, L. Kozak, A. Shevchenko, M. Zipunnikov, R. Campbell, F. Seamon // Проблемы машиностроения. — 2017. — Т. 20, № 1. — С. 62-68. — Бібліогр.: 7 назв. — англ. 0131-2928 https://nasplib.isofts.kiev.ua/handle/123456789/115665 536.2 en Проблемы машиностроения application/pdf Інстиут проблем машинобудування ім. А.М. Підгорного НАН України |
| institution |
Digital Library of Periodicals of National Academy of Sciences of Ukraine |
| collection |
DSpace DC |
| language |
English |
| topic |
Нетрадиционная энергетика Нетрадиционная энергетика |
| spellingShingle |
Нетрадиционная энергетика Нетрадиционная энергетика Solovey, V. Kozak, L. Shevchenko, A. Zipunnikov, M. Campbell, R. Seamon, F. Hydrogen technology of energy storage making use of wind power potential Проблемы машиностроения |
| description |
Описывается разработка универсальных технологий, которые могут быть использованы для обеспечения непрерывной работы опреснительной установки при использовании энергии ветра. Рассмотрены основные принципы реализации электрохимического метода получения водорода и кислорода высокого давления из воды с использованием материалов электродов с переменной валентностью. Предложена система хранения химической энергии в виде сжатого водорода до высоких давлений с последующим его использованием в топливном элементе. Разработанная система характеризуется повышением надежности и эксплуатационной безопасности. Водород-накопительная система позволяет контролировать для установок потребляемую мощность. Это особенно важно, когда основным источником энергии для электролизной установки служит энергия ветра, которая не является постоянной и зависит от климатических факторов. Даны рекомендации по применению данного способа получения водорода (кислорода) с использованием в качестве первичного источника возобновляемых видов энергии (солнца, ветра), отличающихся непостоянством поступления. Сформированы научно-технические принципы создания электрохимических водородных аккумуляторов энергии и предложены пути оптимизации их работы на переменных режимах, характерных для реальных условий эксплуатации энерготехнологических комплексов на базе ветроэнергетической станции. Приведены стоимостные показатели создания и эксплуатации системы генерации водорода в зависимости от уровня давления в электролизере. |
| format |
Article |
| author |
Solovey, V. Kozak, L. Shevchenko, A. Zipunnikov, M. Campbell, R. Seamon, F. |
| author_facet |
Solovey, V. Kozak, L. Shevchenko, A. Zipunnikov, M. Campbell, R. Seamon, F. |
| author_sort |
Solovey, V. |
| title |
Hydrogen technology of energy storage making use of wind power potential |
| title_short |
Hydrogen technology of energy storage making use of wind power potential |
| title_full |
Hydrogen technology of energy storage making use of wind power potential |
| title_fullStr |
Hydrogen technology of energy storage making use of wind power potential |
| title_full_unstemmed |
Hydrogen technology of energy storage making use of wind power potential |
| title_sort |
hydrogen technology of energy storage making use of wind power potential |
| publisher |
Інстиут проблем машинобудування ім. А.М. Підгорного НАН України |
| publishDate |
2017 |
| topic_facet |
Нетрадиционная энергетика |
| url |
https://nasplib.isofts.kiev.ua/handle/123456789/115665 |
| citation_txt |
Hydrogen technology of energy storage making use of wind power potential / V. Solovey, L. Kozak, A. Shevchenko, M. Zipunnikov, R. Campbell, F. Seamon // Проблемы машиностроения. — 2017. — Т. 20, № 1. — С. 62-68. — Бібліогр.: 7 назв. — англ. |
| series |
Проблемы машиностроения |
| work_keys_str_mv |
AT soloveyv hydrogentechnologyofenergystoragemakinguseofwindpowerpotential AT kozakl hydrogentechnologyofenergystoragemakinguseofwindpowerpotential AT shevchenkoa hydrogentechnologyofenergystoragemakinguseofwindpowerpotential AT zipunnikovm hydrogentechnologyofenergystoragemakinguseofwindpowerpotential AT campbellr hydrogentechnologyofenergystoragemakinguseofwindpowerpotential AT seamonf hydrogentechnologyofenergystoragemakinguseofwindpowerpotential |
| first_indexed |
2025-11-27T15:37:07Z |
| last_indexed |
2025-11-27T15:37:07Z |
| _version_ |
1849958422285385728 |
| fulltext |
НЕТРАДИЦИОННАЯ ЭНЕРГЕТИКА
ISSN 0131–2928. Пробл. машиностроения, 2017, Т. 20, № 1 62
1
Victor Solovey, D.Sc.
2
Leonid Kozak, PhD
1
Andrii Shevchenko
1
Mykola Zipunnikov, PhD
3
Robert Campbell
3
Fred Seamon
1
A. N. Podgorny Institute for Mechanical
Engineering Problems, NAS of Ukraine,
Kharkiv, е-maіl:
solovey@ipmach.kharkov.ua
shevchenko84@ukr.net
zipunnikov_n@ukr.net
2
Yuzhnoye State Design Office,
Dnepr, Ukraine,
е-maіl: kozak_dp@mail.ru
3
CAP Holdings Company LLC,
Monterrey, CA, USA, е-maіl:
rcampbell@capholdings.com
fseamon@capholdingsco.com
УДК 536.2
HYDROGEN TECHNOLOGY OF
ENERGY STORAGE MAKING USE
OF WIND POWER POTENTIAL
Описується розробка універсальних технологій, які
можуть бути застосовані для забезпечення
безперервної роботи опріснювальної установки при
використанні енергії вітру. Розглянуто основні
принципи реалізації електрохімічного методу
отримання водню та кисню високого тиску з води із
використанням матеріалів електродів зі змінною
валентністю. Запропоновано систему зберігання
хімічної енергії у вигляді стисненого водню до високих
тисків з подальшим його застосуванням в паливному
елементі, яка характеризується підвищенням
надійності та експлуатаційної безпеки. Надано
рекомендації із застосування даного способу отримання
водню (кисню) з використанням як первинного джерела
відновлюваних видів енергії, що відрізняються
непостійністю надходження (сонце, вітер).
Ключові слова: водень, електролізер,
газопоглинаючий електрод, електрохімічна комірка,
щільність струму, вітро-воднева система
зберігання енергії.
Introduction
The use of wind as a renewable and ecologically clean source of electric power has increased
substantially in regions with developed industrial electricity transmission and distribution networks. In these
situations, wind power is a supplemental power source that can reduce the consumption of fossil fuels and
decrease environmental contamination. In remote areas that are removed from industrial distribution
networks, wind can be used as the main electrical energy source. This article describes the development of a
versatile technology that can be used to provide continuous power for desalination using wind energy and
energy storage [1]. The technology uses advanced electrolysis and fuel cells to efficiently store excess
energy from wind generation as hydrogen for later use in fuel cells. The overall system has the ability to
provide uninterrupted power for desalination or other applications needing energy storage at a reasonable
cost.
Purpose and Statement of the Research Problem
The main obstacle for the use of wind power plants (WPP) is the variable inherent character of wind
flow, which causes the following two basic problems:
1. The process of distributing the wind-generated energy among separate consumers and the WPP
becomes very complicated when operated in combination with a local electric network. Smooth integration
of the variable energy source with an existing power grid is difficult.
2. Electricity generation, storage, and conversion on a large capacity scale are needed to provide an
uninterrupted steady supply of electric power to consumers. This is especially important for the application
involving electricity storage for membrane-based desalination systems. These systems need to be run as long as
possible without having power removed because of a failure mechanism in all existing commercial
membranes known as «creep». It is the physical separation of carrier materials from end caps of the
membrane caused by fluctuations in pressure due to power changes.
Victor Solovey, Leonid Kozak, Andrii Shevchenko, Mykola Zipunnikov, Robert Campbell, Fred Seamon,
2017
НЕТРАДИЦИОННАЯ ЭНЕРГЕТИКА
ISSN 0131–2928. Пробл. машиностроения, 2017, Т. 20, № 1 63
The first problem is solved by choosing the right electrical power equipment and by developing
special-purpose algorithms to control WPP operations within local electric networks.
The second problem can be solved with maximum economic efficiency by applying innovative
hydrogen storage technologies.
Successfully solving these technical problems will significantly increase number of locations where
wind power sources can be employed. This is especially true for small villages located in remote continental
territories, on seacoasts, and on islands where it will enable the installation of electrical power for public
health systems and seawater desalination systems to provide clean drinking water.
Because of the technological features of membrane-based desalination systems, such systems require
that the power supply be steady and the shutdown process controlled. Thus, it is obvious that realizing the
use of such systems is not possible without large-capacity storage of the wind-generated energy.
The Results of Experimental Studies and their Discussion
A water desalination plant operating with a wind power station as its power source could encounter
extraordinary situations resulting from either loss of the power supply because there is no wind or failure of a
system component. In these situations, systematic shutdown of the plant would be required without the loss
of the working capacity of the system.
For this reason, it would be necessary to include energy storage into the technological scheme of the
power-generating complex; sufficient energy must be stored to enable the desalinating plant to continue
operation during periods when the wind power source is not available.
This paper describes a new energy storage system that can be installed as an additional element in
the WPP system. This element involves hydrogen energy storage amounting to 12 MW·h that could supply
uninterrupted energy during non-standard periods of operation and emergency shutdown of the system.
This hydrogen technology has been developed at the Institute of Mechanical Engineering Problems
(IPMach) of the National Academy of Science of Ukraine. The technology developed at IPMach enables the
generation and storage of high-pressure hydrogen without using a compressor. The stored hydrogen then can
be converted to electrical energy using commercial fuel cells. The main element of this hydrogen
accumulation system is an electrolyzer that, in essence, is a generator combined with a hydrogen-storage
system as a component part of the system, thus providing energy storage and subsequent use when needed.
Approaches also have been developed for optimizing various operational modes that are typical of
the actual conditions involving WPPs.
The method used for water electrolysis in our system differs from other hydrogen-generation
methods several ways: the simplicity of its technological scheme, the availability of the raw material, and the
simplicity of the process for generating hydrogen. The main disadvantage of this method, water electrolysis
for hydrogen generation, is that the amount of energy required is very high. To address this disadvantage,
one of the project tasks has been the development of an electrolyzer for generating hydrogen that requires
low power input [2].
Power requirements typical electrolyzers are low because they use 1) platinum group metals as the
electrode material and 2) ion-exchange membranes that are expensive and technically difficult to produce
[3]. This results in increased equipment cost, increased maintenance requirements, decreased reliability, and
the use of resources. These disadvantages can be overcome with the proposed innovative hydrogen-
generation technology. The bases of this technology are the electro-catalytic conversion process and the use
of variable-valency metals as electrode materials. Such metals interact chemically with oxygen generated
under the process of water dissociation.
This new technology for generating high-pressure hydrogen [4–6] consists of two stages that involve
periodically alternating oxidizing and reducing reactions with participation of the active mass of the gas-
absorbing electrode. The principal scheme of the technology with an electrochemical cell and gas-absorbing
electrode is shown in Fig. 1.
The process of hydrogen generation begins with applying negative potential to the passive electrode.
The gas-absorbing active electrode operates as an anode at this stage. The water-dissociation reaction
produces hydrogen and oxygen simultaneously. The hydrogen is isolated at the passive electrode in the
gaseous state, and the oxygen is chemically combined at the active electrode (i.e., it is accumulated as an
oxide). This active electrode is reconditioned to its initial operational state during the following stage of
НЕТРАДИЦИОННАЯ ЭНЕРГЕТИКА
ISSN 0131–2928. Пробл. машиностроения, 2017, Т. 20, № 1 64
electrolyzer operation. This operational sequence is provided by automatic switching of electrodes to act as
anode/cathode electrodes.
Supplying the
electrolysis cell with electric
power is synchronized with an
electromagnetic switch that
controls the gas flow. As a
result, hydrogen is isolated
under high pressure and only
fills a hydrogen pipeline. In
the same manner, oxygen is
fed to a separate pipeline.
Primary cleaning of the
electrolyte streams occurs in
a gas-liquid separator that
separates the flow into
separate gas and liquid
streams.
The water-
dissociation reaction is
initiated by increasing the
voltage at the electrodes
during the gas-generation
process (Fig. 2). Automatic
control of the gas-
generation process is based on the process’s voltage-current characteristics, which were determined
experimentally.
When the voltage value equals the design value, a polarity inversion occurs that simultaneously
switches on the electromagnetic valve to redirect the gas flow into the appropriate pipeline. After redirection,
the passive electrode
becomes the anode, and the
active electrode becomes
the cathode. Accordingly,
isolation of the gaseous
oxygen takes place at a
passive electrode (anode),
while at the cathode, the
active mass of the gas-
absorbing electrode is
reactivated by hydrogen.
Upon reaching the
design value of voltage,
which is used as a
parameter for controlling
the duration of the
oxygen-isolation process,
polarity inversion at
electrodes occurs and recycling takes place.
By using a variable-valency material that chemically bonds oxygen (e.g., spongy iron) as a gas-
absorbing electrode, the working process in area (A – B) of Fig. 2 corresponds to the following reaction:
Fe + 2OH
−
<=> Fe(OH)2 + 2e
–
. (1)
To customer
H2
O2
S
ep
ar
at
o
r
O
2
H2O
Flow switching---
-
S
e
p
a
ra
to
rH
2
To PS
To PS
L
ev
el
s
en
so
rs
L
ev
el
s
en
so
rs
Electrocontact
manometer
To level sennsors
Accessory power
supply
Technological
power supply
. . . . . .
Primary
current
source
Potential
switching
А
V
T
o
c
el
l
C
el
l
To technol.
power supply
Fig. 1. Schematic of an installation with an electrochemical cell using a gas
absorbing electrode
Fig. 2. The cyclograms of the high pressure electrolyzer operation when
voltage is limited from 1.8 to 0.3 V and current is J = 0.02 A/см
2
:
1 – U = 1.8 V; 2 – U = 1.0 V; 3 – U = 0.5 V
НЕТРАДИЦИОННАЯ ЭНЕРГЕТИКА
ISSN 0131–2928. Пробл. машиностроения, 2017, Т. 20, № 1 65
The larger mass of the active electrode reacts with oxygen, which results in more intensive workup
of the electrode mass:
Fe(OH)2 + OH
−
<=> Fe(OH)3 + e
–
. (2)
Area (B – C) of Fig. 2 corresponds to the conversion of Fe(II) to Fe(III) during the hydrogen
isolation cycle, and the oxygen isolation cycle corresponds to electrochemical reduction of iron hydroxides.
Research results have shown that, to provide the low power input needed for hydrogen generation, it
is best to use the process corresponding to the gently sloping area of area (A – B) of Fig. 2 with the
formation of Fe(OH)2 (Reaction (1)). Furthermore, the Fe(OH)2 (under intensive workup, area (В – С)) is
transformed in to Fe(OH)3 (Reaction (2)). The presence of Fe(OH)3 in the active mass of the gas-absorbing
electrode results in additional consumption of electric power. Therefore, to decrease the power required for
the hydrogen-generation process, the electrochemical cell operational mode needs to be optimized.
The proposed method of decreasing the specific power requirements needed during hydrogen
generation involves choosing the voltage value for electrode polarity switching. Based on the research
results, we constructed an electrode assembly that did not have a membrane between the cathode-anode pair
(chromium-nickel steel 08Х18Н10Т-Fe, Fig. 3). This configuration achieved pressures of 15.0 МPа, and its
power consumption was less than 3.9 to 4.0 kW·h/m
3
of hydrogen generated.
Application of the new electrolysis technology, as
compared to the technologies used in traditional electrolyzers,
provides the following advantages:
1. Decreases the power requirements for the production
of the target products up to 10 to 15% (specific power
consumption is from 3.8 to 4.1 kW·h/m
3
of hydrogen generated
and of 0.5 m
3
of oxygen generated);
2. Provides high-pressure gas generation limited only
by the pressure ratings of the materials of construction;
3. Eliminates dividing membranes in the electrodes,
thus improving system reliability and operational safety;
4. Eliminates the use of rare-earth and platinum-group
metals in the hydrogen and oxygen high-pressure
electrochemical generator, thus decreasing the cost of the
primary equipment and, thereby, lowering capital costs;
5. Eliminates the need to compress the generated
hydrogen for transfer to the energy-accumulation and storage-
buffer system.
The most important characteristics of the electrolysis
system are the amounts of generated gases and their pressures
because those two characteristics determine the system design,
size, and cost.
Analysis of the engineering design of the electrolysis technique indicates that increasing the working
pressure requirement to more than 150 to 200 atm significantly increases the capital and operating expenses
for the hydrogen-generation system.
Figure 4 shows reference data for the costs to manufacture and operate the electrolyzers with respect
to the working-pressure levels.
There is a dramatic increase in equipment cost when the electrolyzer operation pressure is ≥ 200 atm
because of the need for higher strength construction materials and more complex technical decisions that, in
turn, require more expensive components (e.g., shutoff and regulating apparatuses, current leads, circulating
and supply pumps, etc.).
After evaluating the total expenditures for creation and operation of the electrolysis hardware, we
have concluded that it is feasible to provide hydrogen pressures from 100 to 200 atm. Such pressures are
achievable using the by IPMach-developed electrolyzers described in this paper. To provide higher hydrogen
pressure, it is necessary to use the combination of variants in a technical scheme of «electrolyzer-
compressor-consumer».
Fig. 3. Electrode assembly without a
membrane for the high-pressure
electrolyzer
НЕТРАДИЦИОННАЯ ЭНЕРГЕТИКА
ISSN 0131–2928. Пробл. машиностроения, 2017, Т. 20, № 1 66
It also is possible to
successfully use metal hydride
thermal sorption installations
instead of mechanical
compressors at pressures near
500 atm. These installations
use heat at a relatively low
temperature (up to 300 °C) to
compress hydrogen. As a
result, the compressing
technology realized by these
installations is more reliable,
safer, and more economical
[7].
Based on the above
analysis, when creating an
energy buffer system for a
desalination complex using
wind-generated power, it
would be reasonable to limit
pressure to 200 atm. To
transfer the hydrogen power
into the autonomous power
source intended for feeding the
desalination plant in
accordance with the given
schedule, it is necessary to
include a hydrogen storage
system.
The gas-cylinder system needed to store 12 MW·h energy is provided by the accumulation and
storage of 4.0×10
3
Nm
3
hydrogen (with a hydrogen thermal value of 10.8 МJ/m
3
). If the construction of the
hydrogen storage system is modular and its base element is assumed to be a gas cylinder manufactured
according to the «12247-80» standard (V = 1.0 m
3
and р = 200 atm.), then 28 gas cylinders would be needed
to accumulate the required energy.
Construction of the hydrogen storage
system in series-parallel connected modules is
envisioned as four rows of seven modules each.
This arrangement for the hydrogen storage
system with a 4.0×10
3
Nm
3
hydrogen capacity
is shown in Fig. 5.
We propose an electrolysis installation
that could produce 220.0 m
3
/h of hydrogen to
fill the above-described storage system with
hydrogen. The technological scheme of a
«block-multi-module» electrolyzer was
developed for this system. The advantages of
the multi-module electrolyzer as compared to a
singular-module electrolyzer are:
1. Comparatively low mass of the
electrolysis cell (module) and, hence, simplicity
of the mounting-assembly operation for
inspections and preventive maintenance
Fig. 4. Total costs per kg of hydrogen for the hydrogen-generation
system vs. the hydrogen pressure level:
1 – the capital expenditures are related to the electrolyzer productivity
in terms of 1 kg of hydrogen per hour. With respect to calculating the
total capital expenditures, the index of the left scale of the diagram is
multiplied by the plant hydrogen productivity index; 2 – The specific
operation expenditures (without expenditures for electrolysis). With
respect to calculating the operation expenditures, the index of the right
scale of the diagram is multiplied by the plant hydrogen productivity
index. When calculating the total operation expenditures it needs to add
the cost of electricity to provide the electrolysis process. This process
takes 44 kW·h per 1 kg of hydrogen
6500
6000
3500
Fig. 5. Schematic arrangement of a gas-cylinder hydrogen
storage system capable of supplying 12.0 МW·h of power
НЕТРАДИЦИОННАЯ ЭНЕРГЕТИКА
ISSN 0131–2928. Пробл. машиностроения, 2017, Т. 20, № 1 67
2. Ability to switch off separate electrolyzer cells during an emergency. This also improves system
serviceability.
A thorough investigation of the electrode assemblies intended for the electrolysis cell body in
conjunction with the gas cylinders proposed for the buffer hydrogen storage system was completed. The
results showed that the module can provide hydrogen productivity of 6 m
3
/h. Therefore, 40 modules would
be needed to construct an electrolyzer that could produce 220.0 m
3
/h of hydrogen. The system provides the
possibility for an overvoltage
of up to 10% of the consumed
power from the wind power
station, which means that the
electrolyzer could continue to
operate for a short period of
time (up to 30 minutes) using
power from a WPP that
exceeds by 10% the nominal
power value certified by the
electrolyzer operation
schedule.
When the electrolyzer
is arranged as a multi-cell unit,
its footprint would be 100 m
3
.
The scheme for a module with
four electrolysis cells (total of
10 for the desired application)
is shown in Fig. 6.
For the power-
technological complex
described in this paper to be
safe and reliable, operation of
the WPP generators and the
high-pressure electrolyzer as a consumer of the electric
power generated by the WPPs must be synchronized.
Original algorithms of the automatic control system
developed at the «Yuzhnoye» State Design Office,
Dnipropetrovsk, Ukraine, will help with this
synchronization. These algorithms are based on current data
about the electrolyzer structural and operational features.
Figure 7 shows an electrolysis installation with its
control system and a 500 kW WPP tower with a 4.9-m base
diameter.
Based on the information discussed above, a buffer
system involving an electrolyzer and hydrogen power
storage fits organically into the technological scheme of a
WPP. Such a buffer system solves the problem of providing
power to a customer (in this case to a seawater desalination
plant) during periods when there is no wind. This is
achieved by a system connecting a windmill-electrolyzer
system to store the needed electrical energy as hydrogen and
then an electrolyzer-fuel cell system to provide power back
to the electrical grid or consumer using appropriate mechanisms for transferring the electrical energy from
the fuel cell to the desired application.
Fig. 6. Principal scheme of the high-pressure electrolyzer:
1 – plunger pump for distilled water supply; 2 – distilled water draining valve;
3 – distilled water vessel; 4 – filling throat; 5 – separators; 6 – electrolysis cell;
7 – gas flow switching; 8 – gas flow lines; 9 – hydrogen feed check valve;
10 – oxygen feed check valve; 11 – hydrogen manometer; 12 – oxygen
manometer; 13 – voltmeter; 14 – ammeter; 15 – feeding and control unit;
16 – fundament; 17 – electrolyte drain valve; 18 – distilled water backflow
prevention valve
Fig. 7. Electrolysis installation composed
of a wind-hydrogen energy storage system
НЕТРАДИЦИОННАЯ ЭНЕРГЕТИКА
ISSN 0131–2928. Пробл. машиностроения, 2017, Т. 20, № 1 68
Conclusions
We have presented in this paper a new technology that electrochemically generates hydrogen and
oxygen. This new technology uses variable-valency metals as electrodes. The technology has a number of
advantages when compared with traditional electrolysis technologies. One significant advantage is high-
pressure gas generation that does not require the use of mechanical compressors to supply the gases to the
buffer storage system. Another advantage is the use of an iron sponge as an active electrode, which decreases
the power needed to generate 1 m
3
of hydrogen (0.5 m
3
of oxygen) by up to 3.85 kW·h. By using an
ingenious switching approach, the technology also provides cyclic hydrogen and oxygen generation that
eliminates the need for ion-exchange membranes to separate the gases.
The systems described in this paper provide high-pressure gas generation along with improved
reliability and operational safety. The hydrogen-generation system allows the chemical reaction rate to be
controlled by controlling the current intensity and, hence, the consumed power can be controlled. This is
especially important when the primary energy source for the electrolysis installation is wind power, which is
not constant and is affected by climatic factors.
Our efforts to further improve the proposed hydrogen-generation method are focused on continued
research into new electrode materials, with an initial focus is on gas-absorbing electrodes. Application of
such electrodes could potentially decrease irreversible losses that occur during the electrochemical reaction
of water dissociation. This would lead to improved operational effectiveness of wind-powered desalination
complexes that use the buffer hydrogen-storage system instead of compressors.
References
1. Autonomous wind-hydrogen stations / V. V. Solovey, V. A. Glazkov, V. K. Pishuk, M. V. Lototsky // Hydrogen
Materials Sci. and Chemistry of Carbon Nanomaterials, 2007. – 861-865 p.
2. Yakimenko, L. M. Water Electrolysis / L. M. Yakimenko. – M.: Chemistry, 1970. – 267 р.
3. Yakimenko, L. M. The Electrode Materials for Applied Electrochemistry / L. M. Yakimenko. – M.: Chemistry, 1977.
– 264 р.
4. Pat. 90421 МПК51, С25В 1/02; С25В 1/04; С25В 1/12. Ukraine. The Electrolysis Device for Generation High-
pressure Hydrogen and Oxygen / V. V. Solovey, O. Ivanovsky, A. Shevchenko, O. Zhirov, O. Makarov. – Made
public on April 26, 2010, Bulletin № 8.
5. Pat. 98705 МПК51, С25В 1/02; С25В 9/04. Ukraine. Mode of Operation of the Electrolysis Device for Generation
High-pressure Hydrogen and Oxygen / V. V. Solovey, A. Shevchenko, O. Zhirov, O. Makarov. – Made public on
June 11, 2012, Bulletin № 11.
6. Pat. 103681 МПК С25В 1/12, С25В 1/03. Ukraine. The Device for Generation High-pressure Hydrogen /
V. V. Solovey, A. Shevchenko, A. Kotenko, O. Makarov. – Made public on November 11, 2013, Bulletin № 21.
7. The Scientific Bases for Creation of the Gas-Turbine Plants Using Thermal-Chemical Compression of an Actuating
Medium / Y. M. Matsevity, V. V. Solovey, V. N. Goloschapov, A. V. Rusanov. – Kiev: The Scientific Ideas, 2011.
– 252 p.
Надійшла до редакції 18.12.16
|