Вплив технологічних параметрів процесу холодної штабової прокатки на продуктивність двохклітьових реверсивних станів
The influence of technological parameters in the production of cold-rolled steel of the main assortment on the average hourly productivity on two-stand reversing mills is investigated. It was established that when rolling tinplate and thin strips of 0.161.0 mm thick with a conditional width of 1000...
Збережено в:
| Дата: | 2023 |
|---|---|
| Автори: | , , |
| Формат: | Стаття |
| Мова: | Українська |
| Опубліковано: |
Physico-technological Institute of Metals and Alloys
2023
|
| Теми: | |
| Онлайн доступ: | https://www.metalsandcasting.com/index.php/mcu/article/view/145 |
| Теги: |
Додати тег
Немає тегів, Будьте першим, хто поставить тег для цього запису!
|
| Назва журналу: | Metal and Casting of Ukraine |
Репозитарії
Metal and Casting of Ukraine| _version_ | 1859471958281814016 |
|---|---|
| author | Василев, Я.Д. Замогильний, Р.О. Гринкевич, В.О. |
| author_facet | Василев, Я.Д. Замогильний, Р.О. Гринкевич, В.О. |
| author_sort | Василев, Я.Д. |
| baseUrl_str | |
| collection | OJS |
| datestamp_date | 2023-06-17T15:43:24Z |
| description | The influence of technological parameters in the production of cold-rolled steel of the main assortment on the average hourly productivity on two-stand reversing mills is investigated. It was established that when rolling tinplate and thin strips of 0.161.0 mm thick with a conditional width of 1000 mm at a speed of 10–30 m/s from rolls of a 15–35 ton bale, the average hourly productivity of these mills varies in the range from 30 to 215 tons .
It is shown that during rolling of tinplate and strips of small thickness from coils of constant weight, the main influence on the level of average hourly productivity is rendered by the speed of rolling, and this effect increases with decreasing strip thickness. Increasing the mass of coils, especially when rolling tinplate and thin strips, is not one of the factors that have a decisive influence on the average hourly productivity. Since the most intensive growth of the average hourly productivity of two-stand reversible mills in the production of rolled products of their main assortment is observed in the range of rolling speeds of 20–25 m/s, the maximum design speed of 22.5 m/s of these mills is reasonable and expedient. In the production of tinplate and thin strips, the mass of coils at the level of 25–28 tons provides an acceptably high level of average hourly productivity when the process is conducted at a speed of up to 20–25 m/s and can be considered necessary and sufficient. Increasing the mass of coils to 30–36 tons seems reasonable when designing two-section reversing mills for the production of products of various sizes up to 0.9–1 million tons per year.
The method for calculating the average hourly productivity on two-stand reversing mills and the materials obtained with it can be used to justify the assortment and determine the parameters of the technology and the main equipment of the two-stand cold rolling mills 1400 and 1750, the construction of which is important for Ukraine. |
| first_indexed | 2026-03-12T15:50:48Z |
| format | Article |
| id | oai:oai.metalsandcasting.com:article-145 |
| institution | Metal and Casting of Ukraine |
| keywords_txt_mv | keywords |
| language | Ukrainian |
| last_indexed | 2026-03-12T15:50:48Z |
| publishDate | 2023 |
| publisher | Physico-technological Institute of Metals and Alloys |
| record_format | ojs |
| spelling | oai:oai.metalsandcasting.com:article-1452023-06-17T15:43:24Z Influence of technological parameters of the cold striping process on the productivity of twostand reversible mills Вплив технологічних параметрів процесу холодної штабової прокатки на продуктивність двохклітьових реверсивних станів Василев, Я.Д. Замогильний, Р.О. Гринкевич, В.О. cold rolling two-stand reversing mill technology productivity parameter velocity mass холодна прокатка двохклітьовий реверсивний стан технологія продуктивність параметр швидкість маса The influence of technological parameters in the production of cold-rolled steel of the main assortment on the average hourly productivity on two-stand reversing mills is investigated. It was established that when rolling tinplate and thin strips of 0.161.0 mm thick with a conditional width of 1000 mm at a speed of 10–30 m/s from rolls of a 15–35 ton bale, the average hourly productivity of these mills varies in the range from 30 to 215 tons . It is shown that during rolling of tinplate and strips of small thickness from coils of constant weight, the main influence on the level of average hourly productivity is rendered by the speed of rolling, and this effect increases with decreasing strip thickness. Increasing the mass of coils, especially when rolling tinplate and thin strips, is not one of the factors that have a decisive influence on the average hourly productivity. Since the most intensive growth of the average hourly productivity of two-stand reversible mills in the production of rolled products of their main assortment is observed in the range of rolling speeds of 20–25 m/s, the maximum design speed of 22.5 m/s of these mills is reasonable and expedient. In the production of tinplate and thin strips, the mass of coils at the level of 25–28 tons provides an acceptably high level of average hourly productivity when the process is conducted at a speed of up to 20–25 m/s and can be considered necessary and sufficient. Increasing the mass of coils to 30–36 tons seems reasonable when designing two-section reversing mills for the production of products of various sizes up to 0.9–1 million tons per year. The method for calculating the average hourly productivity on two-stand reversing mills and the materials obtained with it can be used to justify the assortment and determine the parameters of the technology and the main equipment of the two-stand cold rolling mills 1400 and 1750, the construction of which is important for Ukraine. Досліджено вплив технологічних параметрів при виробництві холоднокатаного прокату основного сортаменту на середньогодинну продуктивність на двохклітьових реверсивних станах. Встановлено, що при прокатці жерсті і тонких штаб товщиною 0,16–1,0 мм, умовною шириною 1000 мм, зі швидкістю 10–30 м/с з рулонів підкату масою 15–35 т, середньогодинна продуктивність цих станів змінюється в діапазоні від 30 до 215 т. Показано, що при прокатці жерсті і штаб малої товщини з рулонів постійної маси основний вплив на рівень середньогодинної продуктивності надає швидкість прокатки, причому зі зменшенням товщини штаби цей вплив зростає. Збільшення маси рулонів, особливо при прокатці жерсті і штаб малої товщини, не відноситься до числа факторів, що значно впливають на середньогодинну продуктивність. Оскільки найбільш інтенсивне зростання середньогодинної продуктивності двохклітьових реверсивних станів при виробництві прокату їх основного сортаменту спостерігається в діапазоні зміни швидкості прокатки 20–25 м/с, максимальна проектна швидкість в 22,5 м/с цих станів є обґрунтованою і доцільною. При виробництві жерсті і тонких штаб маса рулонів на рівні 25–28 т забезпечує прийнятно високий рівень середньогодинної продуктивності при веденні процесу на швидкості до 20–25 м/с і може розглядатися як необхідна і достатня. Збільшення маси рулонів до 30–36 т доцільне при проектуванні двохклітьових реверсивних станів для випуску продукції різноманітного сортаменту об’ємом до 0,9–1 млн т на рік. Наведена в статті методика розрахунку середньогодинної продуктивності на двохклітьових реверсивних станах і отримані з її допомогою матеріали можуть бути використані при обґрунтуванні сортаменту і визначенні параметрів технології і основного обладнання двохклітьових реверсивних станів холодної прокатки 1400 і 1750, спорудження яких актуально для України. Physico-technological Institute of Metals and Alloys 2023-06-17 Article Article Рецензована Стаття application/pdf https://www.metalsandcasting.com/index.php/mcu/article/view/145 Metal and Casting of Ukraine; Vol. 27 No. 1-2 (2019): Metal and Casting of Ukraine Метал та лиття України ; Том 27 № 1-2 (2019): Метал та лиття України 2706-5529 2077-1304 uk https://www.metalsandcasting.com/index.php/mcu/article/view/145/146 Авторське право (c) 2023 Метал та лиття України |
| spellingShingle | холодна прокатка двохклітьовий реверсивний стан технологія продуктивність параметр швидкість маса Василев, Я.Д. Замогильний, Р.О. Гринкевич, В.О. Вплив технологічних параметрів процесу холодної штабової прокатки на продуктивність двохклітьових реверсивних станів |
| title | Вплив технологічних параметрів процесу холодної штабової прокатки на продуктивність двохклітьових реверсивних станів |
| title_alt | Influence of technological parameters of the cold striping process on the productivity of twostand reversible mills |
| title_full | Вплив технологічних параметрів процесу холодної штабової прокатки на продуктивність двохклітьових реверсивних станів |
| title_fullStr | Вплив технологічних параметрів процесу холодної штабової прокатки на продуктивність двохклітьових реверсивних станів |
| title_full_unstemmed | Вплив технологічних параметрів процесу холодної штабової прокатки на продуктивність двохклітьових реверсивних станів |
| title_short | Вплив технологічних параметрів процесу холодної штабової прокатки на продуктивність двохклітьових реверсивних станів |
| title_sort | вплив технологічних параметрів процесу холодної штабової прокатки на продуктивність двохклітьових реверсивних станів |
| topic | холодна прокатка двохклітьовий реверсивний стан технологія продуктивність параметр швидкість маса |
| topic_facet | cold rolling two-stand reversing mill technology productivity parameter velocity mass холодна прокатка двохклітьовий реверсивний стан технологія продуктивність параметр швидкість маса |
| url | https://www.metalsandcasting.com/index.php/mcu/article/view/145 |
| work_keys_str_mv | AT vasilevâd influenceoftechnologicalparametersofthecoldstripingprocessontheproductivityoftwostandreversiblemills AT zamogilʹnijro influenceoftechnologicalparametersofthecoldstripingprocessontheproductivityoftwostandreversiblemills AT grinkevičvo influenceoftechnologicalparametersofthecoldstripingprocessontheproductivityoftwostandreversiblemills AT vasilevâd vplivtehnologíčnihparametrívprocesuholodnoíštabovoíprokatkinaproduktivnístʹdvohklítʹovihreversivnihstanív AT zamogilʹnijro vplivtehnologíčnihparametrívprocesuholodnoíštabovoíprokatkinaproduktivnístʹdvohklítʹovihreversivnihstanív AT grinkevičvo vplivtehnologíčnihparametrívprocesuholodnoíštabovoíprokatkinaproduktivnístʹdvohklítʹovihreversivnihstanív |