Сучасні підходи у створенні високоентропійних та середньоентропійних ливарних алюмінієвих сплавів
The work is devoted to the review of basics of creating high-entropy and medium-entropy alloys (HEAs and MEAs, respectively) and factors that affect on their structural and phase characteristics. The advantages of this type of materials over structural alloys are shown, which is expressed in higher...
Збережено в:
| Дата: | 2023 |
|---|---|
| Автори: | , |
| Формат: | Стаття |
| Мова: | Українська |
| Опубліковано: |
Physico-technological Institute of Metals and Alloys
2023
|
| Теми: | |
| Онлайн доступ: | https://www.metalsandcasting.com/index.php/mcu/article/view/34 |
| Теги: |
Додати тег
Немає тегів, Будьте першим, хто поставить тег для цього запису!
|
| Назва журналу: | Metal and Casting of Ukraine |
Репозитарії
Metal and Casting of Ukraine| _version_ | 1859471908827824128 |
|---|---|
| author | Ліхацький, Іван Ворон, Михайло |
| author_facet | Ліхацький, Іван Ворон, Михайло |
| author_sort | Ліхацький, Іван |
| baseUrl_str | |
| collection | OJS |
| datestamp_date | 2024-01-07T11:35:17Z |
| description | The work is devoted to the review of basics of creating high-entropy and medium-entropy alloys (HEAs and MEAs, respectively) and factors that affect on their structural and phase characteristics. The advantages of this type of materials over structural alloys are shown, which is expressed in higher specific values of mechanical properties, heat resistance and other characteristics that are important for work in extreme conditions. Despite the advantages of high-entropy alloys, their industrial production does not have a wide commercial implementation due to the complexity of the production processes. Such a situation encourages the development of HEAs and MEAs that could be produced on an industrial scale. It is shown that highentropy aluminum-based casting alloys have the highest potential for this, as they are the most suitable for obtaining finished products by using foundry technologies.
Analysis of modern researches has shown that development of aluminum-based high-entropy and medium-entropy casting alloys, needs to use components that have an eutectic transformation with aluminum and with each other or which do not form high-temperature intermetallics at low concentrations up to 5 % at. The most suitable components for this are Si, Mg, Zn, Cr, Mn, Fe, Co, Ni, Cu, Ti and V. It gives possibility and rises chances to obtain alloys with a relatively low melting point and high casting properties. Preparation of Al-based HEA melts should be based on the use of concentrated and multicomponent master alloys. |
| first_indexed | 2026-03-12T15:50:01Z |
| format | Article |
| id | oai:oai.metalsandcasting.com:article-34 |
| institution | Metal and Casting of Ukraine |
| keywords_txt_mv | keywords |
| language | Ukrainian |
| last_indexed | 2026-03-12T15:50:01Z |
| publishDate | 2023 |
| publisher | Physico-technological Institute of Metals and Alloys |
| record_format | ojs |
| spelling | oai:oai.metalsandcasting.com:article-342024-01-07T11:35:17Z Modern approaches in the creation of high-entropy and medium-entropy cast aluminum alloys Сучасні підходи у створенні високоентропійних та середньоентропійних ливарних алюмінієвих сплавів Ліхацький, Іван Ворон, Михайло cast aluminum alloys high-entropy alloys medium-entropy alloys material design new materials ливарні алюмінієві сплави високоентропійні сплави середньоентропійні сплави дизайн матеріалів нові матеріали The work is devoted to the review of basics of creating high-entropy and medium-entropy alloys (HEAs and MEAs, respectively) and factors that affect on their structural and phase characteristics. The advantages of this type of materials over structural alloys are shown, which is expressed in higher specific values of mechanical properties, heat resistance and other characteristics that are important for work in extreme conditions. Despite the advantages of high-entropy alloys, their industrial production does not have a wide commercial implementation due to the complexity of the production processes. Such a situation encourages the development of HEAs and MEAs that could be produced on an industrial scale. It is shown that highentropy aluminum-based casting alloys have the highest potential for this, as they are the most suitable for obtaining finished products by using foundry technologies. Analysis of modern researches has shown that development of aluminum-based high-entropy and medium-entropy casting alloys, needs to use components that have an eutectic transformation with aluminum and with each other or which do not form high-temperature intermetallics at low concentrations up to 5 % at. The most suitable components for this are Si, Mg, Zn, Cr, Mn, Fe, Co, Ni, Cu, Ti and V. It gives possibility and rises chances to obtain alloys with a relatively low melting point and high casting properties. Preparation of Al-based HEA melts should be based on the use of concentrated and multicomponent master alloys. Роботу присвячено огляду основ створення високоентропійних та середньоентропійних сплавів (ВЕС та СЕС відповідно) та чинників, які впливають на їх структурно-фазові характеристики. Показано переваги даного типу матеріалів перед конструкційними сплавами, що виражається у вищих питомих значеннях механічних властивостей, жароміцності та інших характеристиках, важливих для роботи в екстремальних умовах. Незважаючи на переваги та перспективність високоентропійних сплавів, їх промислове виробництво не має широкого комерційного впровадження через складність процесів виробництва. Така ситуація спонукає до розробки ВЕС і СЕС, які могли б вироблятися в промислових масштабах. Показано, що найвищий потенціал для цього мають ливарні високоентропійні сплави на основі алюмінію, як найбільш придатні для ливарних технологій одержання готових виробів з них. Аналіз сучасних досліджень показав, що для створення ливарних високоентропійних та середньоентропійних сплавів на основі алюмінію потрібно використовувати головним чином компоненти, які мають з алюмінієм та між собою евтектичне перетворення або не утворюють високотемпературні інтерметаліди при низьких концентраціях до 5 % ат. Найбільш підходять для цього Si, Mg, Zn, Cr, Mn, Fe, Co, Ni, Cu, Ti та V. Це дасть змогу одержати сплави з відносно низькою температурою плавлення та високими ливарними властивостями. Приготування розплавів ВЕС на основі алюмінію потребуватиме застосування концентрованих і багатокомпонентних лігатур. Physico-technological Institute of Metals and Alloys 2023-05-21 Article Article Рецензована Стаття application/pdf https://www.metalsandcasting.com/index.php/mcu/article/view/34 10.15407/steelcast2022.03.102 Metal and Casting of Ukraine; Vol. 30 No. 3 (2022): Метал та лиття України Метал та лиття України ; Том 30 № 3 (2022): Метал та лиття України 2706-5529 2077-1304 uk https://www.metalsandcasting.com/index.php/mcu/article/view/34/34 Авторське право (c) 2023 Метал та лиття України |
| spellingShingle | ливарні алюмінієві сплави високоентропійні сплави середньоентропійні сплави дизайн матеріалів нові матеріали Ліхацький, Іван Ворон, Михайло Сучасні підходи у створенні високоентропійних та середньоентропійних ливарних алюмінієвих сплавів |
| title | Сучасні підходи у створенні високоентропійних та середньоентропійних ливарних алюмінієвих сплавів |
| title_alt | Modern approaches in the creation of high-entropy and medium-entropy cast aluminum alloys |
| title_full | Сучасні підходи у створенні високоентропійних та середньоентропійних ливарних алюмінієвих сплавів |
| title_fullStr | Сучасні підходи у створенні високоентропійних та середньоентропійних ливарних алюмінієвих сплавів |
| title_full_unstemmed | Сучасні підходи у створенні високоентропійних та середньоентропійних ливарних алюмінієвих сплавів |
| title_short | Сучасні підходи у створенні високоентропійних та середньоентропійних ливарних алюмінієвих сплавів |
| title_sort | сучасні підходи у створенні високоентропійних та середньоентропійних ливарних алюмінієвих сплавів |
| topic | ливарні алюмінієві сплави високоентропійні сплави середньоентропійні сплави дизайн матеріалів нові матеріали |
| topic_facet | cast aluminum alloys high-entropy alloys medium-entropy alloys material design new materials ливарні алюмінієві сплави високоентропійні сплави середньоентропійні сплави дизайн матеріалів нові матеріали |
| url | https://www.metalsandcasting.com/index.php/mcu/article/view/34 |
| work_keys_str_mv | AT líhacʹkijívan modernapproachesinthecreationofhighentropyandmediumentropycastaluminumalloys AT voronmihajlo modernapproachesinthecreationofhighentropyandmediumentropycastaluminumalloys AT líhacʹkijívan sučasnípídhodiustvorennívisokoentropíjnihtaserednʹoentropíjnihlivarnihalûmíníêvihsplavív AT voronmihajlo sučasnípídhodiustvorennívisokoentropíjnihtaserednʹoentropíjnihlivarnihalûmíníêvihsplavív |