Контроль якості безперервнолитої заготовки з низьковуглецевої сталі для виготовлення катанки
It was stated that the breakage of processing low-carbon wire rod during wire drawing directly hinges not only on the microstructure, surface quality and the presence of defects on it, but also on the content of non-metallic inclusions. An analysis of the requirements of the relevant regulatory docu...
Збережено в:
| Дата: | 2023 |
|---|---|
| Автори: | , , |
| Формат: | Стаття |
| Мова: | Українська |
| Опубліковано: |
Physico-technological Institute of Metals and Alloys
2023
|
| Теми: | |
| Онлайн доступ: | https://www.metalsandcasting.com/index.php/mcu/article/view/72 |
| Теги: |
Додати тег
Немає тегів, Будьте першим, хто поставить тег для цього запису!
|
| Назва журналу: | Metal and Casting of Ukraine |
Репозитарії
Metal and Casting of Ukraine| _version_ | 1859471925069217792 |
|---|---|
| author | Балаханова, Тетяна Левченко, Геннадій Рибалка, Є. М. |
| author_facet | Балаханова, Тетяна Левченко, Геннадій Рибалка, Є. М. |
| author_sort | Балаханова, Тетяна |
| baseUrl_str | |
| collection | OJS |
| datestamp_date | 2023-05-27T10:16:49Z |
| description | It was stated that the breakage of processing low-carbon wire rod during wire drawing directly hinges not only on the microstructure, surface quality and the presence of defects on it, but also on the content of non-metallic inclusions. An analysis of the requirements of the relevant regulatory documents for the quality of low-carbon wire rod was carried out. It is shown that there are no regulated requirements for the cleanliness of low-carbon steel wire rod for non-metallic inclusions in the current domestic regulatory documentation, which does not allow to prevent breakage during drawing precisely because of the abundance of defects. The quality of continuous cast ingots of various sizes from low-carbon steel, the presence and nature of macrodefects, the type and morphology of non-metallic inclusions, as well as the transformation of defects in the finished wire rod have been investigated. Recommendations were given to manufacturers and consumers of low-carbon wire rod. It is advisable to recommend standardizing the level and type of non-metallic inclusions when accepting products and establishing the contamination limit with non-metallic inclusions to consumers of low-carbon wire rod for subsequent processing into wire. It is shown that the analysis of the non-metallic inclusions content in the continuous cast ingot intended for the manufacture of low-carbon wire rod is uninformative. Given this, the manufacturers of low-carbon wire rod are recommended to carry out work to improve the quality of the initial continuous cast ingot and to strengthen the requirements for the macrostructure, in particular, on the item "edge point contamination". |
| first_indexed | 2026-03-12T15:50:16Z |
| format | Article |
| id | oai:oai.metalsandcasting.com:article-72 |
| institution | Metal and Casting of Ukraine |
| keywords_txt_mv | keywords |
| language | Ukrainian |
| last_indexed | 2026-03-12T15:50:16Z |
| publishDate | 2023 |
| publisher | Physico-technological Institute of Metals and Alloys |
| record_format | ojs |
| spelling | oai:oai.metalsandcasting.com:article-722023-05-27T10:16:49Z Quality control of continuous cast ingot from low-carbon steel for wire rod production Контроль якості безперервнолитої заготовки з низьковуглецевої сталі для виготовлення катанки Балаханова, Тетяна Левченко, Геннадій Рибалка, Є. М. low carbon wire rod non-metallic inclusions continuous cast ingot macrostructure низьковуглецева катанка неметалеві включення безперервнолита заготовка макроструктура It was stated that the breakage of processing low-carbon wire rod during wire drawing directly hinges not only on the microstructure, surface quality and the presence of defects on it, but also on the content of non-metallic inclusions. An analysis of the requirements of the relevant regulatory documents for the quality of low-carbon wire rod was carried out. It is shown that there are no regulated requirements for the cleanliness of low-carbon steel wire rod for non-metallic inclusions in the current domestic regulatory documentation, which does not allow to prevent breakage during drawing precisely because of the abundance of defects. The quality of continuous cast ingots of various sizes from low-carbon steel, the presence and nature of macrodefects, the type and morphology of non-metallic inclusions, as well as the transformation of defects in the finished wire rod have been investigated. Recommendations were given to manufacturers and consumers of low-carbon wire rod. It is advisable to recommend standardizing the level and type of non-metallic inclusions when accepting products and establishing the contamination limit with non-metallic inclusions to consumers of low-carbon wire rod for subsequent processing into wire. It is shown that the analysis of the non-metallic inclusions content in the continuous cast ingot intended for the manufacture of low-carbon wire rod is uninformative. Given this, the manufacturers of low-carbon wire rod are recommended to carry out work to improve the quality of the initial continuous cast ingot and to strengthen the requirements for the macrostructure, in particular, on the item "edge point contamination". Обривання переробної низьковуглецевої катанки при волочінні на дріт безпосередньо залежить не тільки від мікроструктури, якості поверхні та наявності на ній дефектів, але й від вмісту неметалевих включень. Досліджено якість вихідних безперервнолитих заготовок різного розміру з низьковуглецевої сталі, які призначені для виготовлення катанки, визначено вид і характер розташування макродефектів, тип і морфологію неметалевих включень, а також трансформацію цих дефектів у готовій катанці. Показано, що забрудненість безперервнолитої заготовки неметалевими включеннями призводить до виготовлення неякісної катанки, яка навіть при відповідності всім вимогам чинної нормативної документації, має низьку технологічність і під час переробки її на дріт руйнується з розшаруванням. Проведено аналіз вимог відповідної нормативної документації щодо якості низьковуглецевої катанки. Показана відсутність регламентованих вимог до чистоти катанки з низьковуглецевої сталі за неметалевими включеннями, що не дозволяє попередити обривність при волочінні саме через велику кількість дефектів. Надано рекомендації як виробникам, так і споживачам низьковуглецевої катанки. Споживачам низьковуглецевої катанки для подальшого переробляння на дріт є доцільним рекомендувати нормування рівня та виду неметалевих включень при прийманні продукції і встановленні границі забрудненості неметалевими включеннями. Показано, що проведення аналізу вмісту неметалевих включень у вихідній безперервнолитій заготовці, яка призначена для виготовлення низьковуглецевої катанки, є неінформативним. Тому для виробників низьковуглецевої катанки рекомендується провести роботи щодо підвищення якості вихідної безперервнолитої заготовки та посилити вимоги до макроструктури, зокрема за пунктом «крайові точкові забруднення». Physico-technological Institute of Metals and Alloys 2023-05-27 Article Article Рецензована Стаття application/pdf https://www.metalsandcasting.com/index.php/mcu/article/view/72 Metal and Casting of Ukraine; Vol. 29 No. 3 (2021): Metal and Casting of Ukraine Метал та лиття України ; Том 29 № 3 (2021): Метал та лиття України 2706-5529 2077-1304 uk https://www.metalsandcasting.com/index.php/mcu/article/view/72/72 Авторське право (c) 2023 Метал та лиття України |
| spellingShingle | низьковуглецева катанка неметалеві включення безперервнолита заготовка макроструктура Балаханова, Тетяна Левченко, Геннадій Рибалка, Є. М. Контроль якості безперервнолитої заготовки з низьковуглецевої сталі для виготовлення катанки |
| title | Контроль якості безперервнолитої заготовки з низьковуглецевої сталі для виготовлення катанки |
| title_alt | Quality control of continuous cast ingot from low-carbon steel for wire rod production |
| title_full | Контроль якості безперервнолитої заготовки з низьковуглецевої сталі для виготовлення катанки |
| title_fullStr | Контроль якості безперервнолитої заготовки з низьковуглецевої сталі для виготовлення катанки |
| title_full_unstemmed | Контроль якості безперервнолитої заготовки з низьковуглецевої сталі для виготовлення катанки |
| title_short | Контроль якості безперервнолитої заготовки з низьковуглецевої сталі для виготовлення катанки |
| title_sort | контроль якості безперервнолитої заготовки з низьковуглецевої сталі для виготовлення катанки |
| topic | низьковуглецева катанка неметалеві включення безперервнолита заготовка макроструктура |
| topic_facet | low carbon wire rod non-metallic inclusions continuous cast ingot macrostructure низьковуглецева катанка неметалеві включення безперервнолита заготовка макроструктура |
| url | https://www.metalsandcasting.com/index.php/mcu/article/view/72 |
| work_keys_str_mv | AT balahanovatetâna qualitycontrolofcontinuouscastingotfromlowcarbonsteelforwirerodproduction AT levčenkogennadíj qualitycontrolofcontinuouscastingotfromlowcarbonsteelforwirerodproduction AT ribalkaêm qualitycontrolofcontinuouscastingotfromlowcarbonsteelforwirerodproduction AT balahanovatetâna kontrolʹâkostíbezperervnolitoízagotovkiznizʹkovuglecevoístalídlâvigotovlennâkatanki AT levčenkogennadíj kontrolʹâkostíbezperervnolitoízagotovkiznizʹkovuglecevoístalídlâvigotovlennâkatanki AT ribalkaêm kontrolʹâkostíbezperervnolitoízagotovkiznizʹkovuglecevoístalídlâvigotovlennâkatanki |