НОВИЙ НАПРЯМОК В РОЗРОБЦІ РІДКИХ ГАРТУВАЛЬНИХ СЕРЕДОВИЩ
It is shown that in contrast to well known surface active additives (SAA), affecting physical properties of a liquid, the elimination of film boiling during quenching is achieved by creation of the thin polymeric layer on the surface of hardened metal. It is performed by using special polymers of op...
Збережено в:
| Дата: | 2019 |
|---|---|
| Автори: | , , , |
| Формат: | Стаття |
| Мова: | English |
| Опубліковано: |
Institute of Engineering Thermophysics of NAS of Ukraine
2019
|
| Онлайн доступ: | https://ihe.nas.gov.ua/index.php/journal/article/view/348 |
| Теги: |
Додати тег
Немає тегів, Будьте першим, хто поставить тег для цього запису!
|
| Назва журналу: | Thermophysics and Thermal Power Engineering |
Репозитарії
Thermophysics and Thermal Power Engineering| id |
oai:ojs2.ihenasgovua.s43.yourdomain.com.ua:article-348 |
|---|---|
| record_format |
ojs |
| spelling |
oai:ojs2.ihenasgovua.s43.yourdomain.com.ua:article-3482019-12-19T13:53:19Z NEW DIRECTION IN LIQUID QUENCHING MEDIA DEVELOPMENT НОВИЙ НАПРЯМОК В РОЗРОБЦІ РІДКИХ ГАРТУВАЛЬНИХ СЕРЕДОВИЩ Kobasko, N.I. Moskalenko, A.A. Logvinenko, P.N. Dobryvechir, V.V. It is shown that in contrast to well known surface active additives (SAA), affecting physical properties of a liquid, the elimination of film boiling during quenching is achieved by creation of the thin polymeric layer on the surface of hardened metal. It is performed by using special polymers of optimal concentration in water. The obtained insulating polymeric layer decreases initial heat flux density below its critical value and by this way eliminates completely the film boiling without affecting clearly the physical properties of a liquid. Based on this fact and on the principle of decreasing distortion, quench crack formation, and increasing strength of material during intensive quenching, it is proposed to use low concentration of special polymers instead of their high concentration in water. All of this results in significant strengthening of metal, saves costly materials, and increases service life of hardened products. Показано, что в отличие от поверхностно- активных веществ (ПАВ), изменяющих физические свойства жидкости, устранение паровой пленки достигается образованием тонкого полимерного покрытия на поверхности металла. Это осуществляется использованием водных растворов специальных полимеров. Покрытие уменьшает начальный тепловой поток ниже критического значения и тем самым устраняет паровую пленку, не оказывая заметного влияния на физические свойства жидкости. Основываясь на этом факте и принципе снижения деформаций, устранения трещин и существенного упрочнения стали интенсивной закалкой, предложено использовать низкие концентрации разных полимеров вместо их высоких концентраций. Это приводит к существенному упрочнению металла, экономии материалов и увеличению долговечности работы закаленных изделий. Показано, що на противагу поверхнево- активним речовинам (ПАР), змінюючих суттєво фізичні властивості рідини, ліквідація парової плівки при гартуванні відбувається завдяки утворенню теплоізоляційного покриття на поверхні металу. Це досягається використанням водних розчинів спеціальних полімерів. Теплоізоляційне полімерне покриття зменшує початковий тепловий потік нижче його критичного значення, ліквідуючи парову плівку без суттєвої зміни фізичних властивостей рідини. Базуючись на цьому факті та принципі зниження деформацій, тріщиноутворення і зміцнення матеріалу при інтенсивному гартуванні, запропоновано використовувати низькі концентрації полімерів замість їх високих концентрацій. Це призводить до значного зміцнення металу, економії матеріалів та зростанню довговічності загартованих виробів. Institute of Engineering Thermophysics of NAS of Ukraine 2019-05-30 Article Article application/pdf https://ihe.nas.gov.ua/index.php/journal/article/view/348 10.31472/ttpe.3.2019.5 Thermophysics and Thermal Power Engineering; Vol 41 No 3 (2019): Thermophysics and Thermal Power Engineering; 33-40 Теплофизика и Теплоэнергетика; Vol 41 No 3 (2019): Thermophysics and Thermal Power Engineering; 33-40 Теплофізика та Теплоенергетика; Vol 41 No 3 (2019): Thermophysics and Thermal Power Engineering; 33-40 2663-7235 10.31472/ttpe.3.2019 en https://ihe.nas.gov.ua/index.php/journal/article/view/348/290 |
| institution |
Thermophysics and Thermal Power Engineering |
| baseUrl_str |
|
| datestamp_date |
2019-12-19T13:53:19Z |
| collection |
OJS |
| language |
English |
| format |
Article |
| author |
Kobasko, N.I. Moskalenko, A.A. Logvinenko, P.N. Dobryvechir, V.V. |
| spellingShingle |
Kobasko, N.I. Moskalenko, A.A. Logvinenko, P.N. Dobryvechir, V.V. НОВИЙ НАПРЯМОК В РОЗРОБЦІ РІДКИХ ГАРТУВАЛЬНИХ СЕРЕДОВИЩ |
| author_facet |
Kobasko, N.I. Moskalenko, A.A. Logvinenko, P.N. Dobryvechir, V.V. |
| author_sort |
Kobasko, N.I. |
| title |
НОВИЙ НАПРЯМОК В РОЗРОБЦІ РІДКИХ ГАРТУВАЛЬНИХ СЕРЕДОВИЩ |
| title_short |
НОВИЙ НАПРЯМОК В РОЗРОБЦІ РІДКИХ ГАРТУВАЛЬНИХ СЕРЕДОВИЩ |
| title_full |
НОВИЙ НАПРЯМОК В РОЗРОБЦІ РІДКИХ ГАРТУВАЛЬНИХ СЕРЕДОВИЩ |
| title_fullStr |
НОВИЙ НАПРЯМОК В РОЗРОБЦІ РІДКИХ ГАРТУВАЛЬНИХ СЕРЕДОВИЩ |
| title_full_unstemmed |
НОВИЙ НАПРЯМОК В РОЗРОБЦІ РІДКИХ ГАРТУВАЛЬНИХ СЕРЕДОВИЩ |
| title_sort |
новий напрямок в розробці рідких гартувальних середовищ |
| title_alt |
NEW DIRECTION IN LIQUID QUENCHING MEDIA DEVELOPMENT |
| description |
It is shown that in contrast to well known surface active additives (SAA), affecting physical properties of a liquid, the elimination of film boiling during quenching is achieved by creation of the thin polymeric layer on the surface of hardened metal. It is performed by using special polymers of optimal concentration in water. The obtained insulating polymeric layer decreases initial heat flux density below its critical value and by this way eliminates completely the film boiling without affecting clearly the physical properties of a liquid. Based on this fact and on the principle of decreasing distortion, quench crack formation, and increasing strength of material during intensive quenching, it is proposed to use low concentration of special polymers instead of their high concentration in water. All of this results in significant strengthening of metal, saves costly materials, and increases service life of hardened products.
|
| publisher |
Institute of Engineering Thermophysics of NAS of Ukraine |
| publishDate |
2019 |
| url |
https://ihe.nas.gov.ua/index.php/journal/article/view/348 |
| work_keys_str_mv |
AT kobaskoni newdirectioninliquidquenchingmediadevelopment AT moskalenkoaa newdirectioninliquidquenchingmediadevelopment AT logvinenkopn newdirectioninliquidquenchingmediadevelopment AT dobryvechirvv newdirectioninliquidquenchingmediadevelopment AT kobaskoni novijnaprâmokvrozrobcírídkihgartuvalʹnihseredoviŝ AT moskalenkoaa novijnaprâmokvrozrobcírídkihgartuvalʹnihseredoviŝ AT logvinenkopn novijnaprâmokvrozrobcírídkihgartuvalʹnihseredoviŝ AT dobryvechirvv novijnaprâmokvrozrobcírídkihgartuvalʹnihseredoviŝ |
| first_indexed |
2025-12-17T13:55:24Z |
| last_indexed |
2025-12-17T13:55:24Z |
| _version_ |
1851763955541737472 |